← All trade remedy orders

Scope of the measure

The merchandise covered by the Order includes certain steel nails having a shaft length up to 12 inches. Certain steel nails include, but are not limited to, nails made of round wire and nails that are cut. Certain steel nails may be of one piece construction or constructed of two or more pieces. Certain steel nails may be produced from any type of steel, and have a variety of finishes, heads, shanks, point types, shaft lengths and shaft diameters. Finishes include, but are not limited to, coating in vinyl, zinc (galvanized, whether by electroplating or hot-dipping one or more times), phosphate cement, and paint. Head styles include, but are not limited to, flat, projection, cupped, oval, brad, headless, double, countersunk, and sinker. Shank styles include, but are not limited to, smooth, barbed, screw threaded, ring shank and fluted shank styles. Screw-threaded nails subject to the Order are driven using direct force and not by turning the fastener using a tool that engages with the head. Point styles include, but are not limited to, diamond, blunt, needle, chisel and no point. Certain steel nails may be sold in bulk, or they may be collated into strips or coils using materials such as plastic, paper, or wire. Certain steel nails subject to the Order are currently classified under the Harmonized Tariff Schedule of the United States (HTSUS) subheadings 7317.00.55, 7317.00.65, and 7317.00.75. Excluded from the scope of the Order are steel nails specifically enumerated and identified in ASTM Standard F 1667 (2011 revision) as Type I, Style 20 nails, whether collated or in bulk, and whether or not galvanized. Also excluded from the scope of the Order are the following products: non-collated (i.e., hand-drive or bulk), two-piece steel nails having plastic or steel washers (caps) already assembled to the nail, having a bright or galvanized finish, a ring, fluted or spiral shank, an actual length of 0.500'' to 8'', inclusive; an actual shank diameter of 0.1015'' to 0.166'', inclusive; and an actual washer or cap diameter of 0.900'' to 1.10'', inclusive; non-collated (i.e., hand-drive or bulk), steel nails having a bright or galvanized finish, a smooth, barbed or ringed shank, an actual length of 0.500'' to 4'', inclusive; an actual shank diameter of 0.1015'' to 0.166'', inclusive; and an actual head diameter of 0.3375'' to 0.500'', inclusive; wire collated steel nails, in coils, having a galvanized finish, a smooth, barbed or ringed shank, an actual length of 0.500'' to 1.75'', inclusive; an actual shank diameter of 0.116'' to 0.166'', inclusive; and an actual head diameter of 0.3375'' to 0.500'', inclusive; non-collated (i.e., hand-drive or bulk), steel nails having a convex head (commonly known as an umbrella head), a smooth or spiral shank, a galvanized finish, an actual length of 1.75'' to 3'', inclusive; an actual shank diameter of 0.131'' to 0.152'', inclusive; and an actual head diameter of 0.450'' to 0.813'', inclusive; corrugated nails. A corrugated nail is made of a small strip of corrugated steel with sharp points on one side; thumb tacks, which are currently classified under HTSUS 7317.00.10.00; fasteners suitable for use in powder-actuated hand tools, not threaded and threaded, which are currently classified under HTSUS 7317.00.20 and 7317.00.30; certain steel nails that are equal to or less than 0.0720 inches in shank diameter, round or rectangular in cross section, between 0.375 inches and 2.5 inches in length, and that are collated with adhesive or polyester film tape backed with a heat seal adhesive; and fasteners having a case hardness greater than or equal to 50 HRC, a carbon content greater than or equal to 0.5 percent, a round head, a secondary reduced-diameter raised head section, a centered shank, and a smooth symmetrical point, suitable for use in gas-actuated hand tools. While the HTSUS subheadings are provided for convenience and customs purposes, the written description of the scope of the Order is dispositive. Continuation of the Order As a result of the determinations by Commerce and the ITC that revocation of the Order would likely lead to a continuation or recurrence of dumping and material injury to an industry in the United States, pursuant to section 751(d)(2) of the Act and 19 CFR 351.218(a), Commerce hereby orders the continuation of the Order. U.S. Customs and Border Protection will continue to collect AD cash deposits at the rates in effect at the time of entry for all imports of subject merchandise. The effective date of the continuation of the Order will be August 31, 2023. Pursuant to section 751(c)(2) of the Act and 19 CFR 351.218(c)(2), Commerce intends to initiate the next five-year review of the Order not later than 30 days prior to the fifth anniversary of the date of the last determination by the ITC. See ITC Final Determination.

Scope text quoted verbatim from the Federal Register notice. Scope text retrieved: 2026-10-19T16:17:45Z. Record last fetched: 2026-10-16T15:26:37Z. Verify against the official notice before relying on it.

HTS codes covered by this order

Related orders — same primary origin

• A-520-807 · Circular Welded Carbon-Quality Steel Pipe · Antidumping (AD) · latest event 2026-10-06
• A-520-803 · Polyethylene Terephthalate Film, Sheet, and Strip · Antidumping (AD) · latest event 2020-11-10

Quoting this shipment? Estimate its landed rate in the US tariff calculator, set up change alerts in a free ExportSonar account, or compare plan limits and pricing.